Washing machines of the Samsung brand are widely represented on the domestic market. Their popularity is associated with high reliability and the use of innovative technologies.
But even such equipment is not immune from possible breakdowns. One option is the need to replace the belt. This type of work is a moderately complex repair, and you can even do it yourself.
We will tell you in the article how to change the belt on a Samsung washing machine (remove the old one, put on a new one).
Signs that a part requires replacement
The need to replace a belt is not a common problem. Worn parts can become noticeable during prolonged or improper use of the washing machine.
The average service life of a washing machine belt is 6 years. The need for replacement during longer use is a normal situation.
with regular violation of the rules, for example, overloading laundry, can accelerate the wear of a part
In some cases, a problem with the drive belt may be indicated by a complete stop of the washing machine and the display of code E4, , UB. On machines not equipped with a display, all mode lights blink and the second temperature indicator from the top lights up.
A problem with the drive belt does not always cause an error code to appear.
It is necessary to pay attention to the following failure situations:
- when water is filled into the drum and the motor is running, the drum does not rotate;
- the engine runs intermittently;
- after the start of the work cycle, despite the engine running, a freeze occurs;
- free rotation of the drum when the engine is not running.
- Uncharacteristic noise when washing.
If the part itself has a rough surface, pellets have formed on the surface and on the elements that are in contact with the belt, or delamination, then replacement is definitely needed. But this can only be determined through direct access.
If problems with the drive belt occur frequently, professional diagnostics of the machine by a specialist is necessary.
Preparation for the process
Replacing the drive belt is carried out by partially disassembling the structure of the washing machine. Therefore, you need to prepare:
If there is water in the washing machine, it must be drained and the laundry must be removed from the drum.- Disconnect the device from all communications. You should not only turn off the machine with the button, but also remove the plug from the socket.
- Move the machine so that you can access the back wall.
- Prepare tools - a set of screwdrivers.
If the part has flown off for the first time and has no visual damage, it can simply be returned to its place without replacement.
Two belt access options
The belt can be accessed from the back wall of the washing machine, if it is removable, or through the top.
Since many Samsung models do not have access to the elements of the washing machine from the rear wall, the job of replacing the belt becomes much more complicated.
Procedure for machines with a removable back panel:
- Unscrew all the screws that hold this cover in place.
- Remove the cover. This allows you to get a good overview and convenience when replacing parts.
Otherwise, you will have to work through the top of the machine. For this, the steps will be as follows:
- unscrew the screws that hold the top cover;
- lightly push the cover towards the back wall so that it is removed from the grooves;
- remove the cover.
The immediate procedure for replacing the belt does not depend on the method of access to the part.
Procedure for putting on a broken drive belt
The order is as follows:
- Disassembling the washing machine. To get to the belt, as a rule, you need to remove the back wall in front-loading machines and the side wall in vertical ones.
- Diagnostics. The technician inspects the belt itself for damage, as well as the washer, to eliminate breakdowns that could lead to damage or falling off of the belt.
- Belt tension. If the belt and machine are in order, the master tightens the belt - first on the motor pulley, and then distributes it over the drum pulley with a clockwise rotational movement (like putting on a bicycle chain). The tension is checked.
- Machine assembly.
Attention! If, during diagnostics, the technician discovers other breakdowns of the machine that lead to the belt jumping off the pulley, he will offer you a comprehensive repair, since otherwise putting on the belt will not have the desired effect, and after a while it will fly off again.
In order to put on or change the drive belt of a washing machine, as with any repair work, appropriate experience is required. If you find that the belt has come off or broken, it is better to entrust the repair work to the RemBytTech specialists:
Within 24 hours of your request, a specialist will come to you, determine the cause of the problem with the drive belt, and fix it with a guarantee of up to 9 months. Contact us!
Replacing a belt in a Samsung washing machine is a moderately complex repair that can be done by advanced beginners. If you don’t want to pay for a replacement technician, you can save up to 1000 rubles.
For enthusiasts, we have prepared a review with practical tips on how to install a belt on a Samsung washing machine.
READ MORE: The water heater plug is heating up - Technical Forum
The following reasons push washing machine owners to replace parts:
- An uncharacteristic noise or rumble is heard during washing.
- Upon inspection, the surface of the part is rough (looks like dirt), and when rubbed, it rolls into balls.
- You have been using the machine for more than 6 years - this is usually the service life of the part.
If at least one of the above reasons is confirmed, you need to carry out a technical inspection of the machine - you may need to replace the part.
Important! In the model range of this brand, the back panel cannot be removed, so repairs are somewhat more complicated.
How to install a new one?
In order to replace the belt, you must first dismantle the old part and then install the new part. First you need to determine whether it is on the drum pulley. If it's not there, it's probably torn or fallen off completely and fallen to the bottom.
How to tension a new belt? Procedure for machines with a non-removable back side:
The car must be tilted towards itself so that the tank sag towards the hatch, and the gap between it and the rear wall becomes larger.- The old part must be pryed off with a screwdriver and removed from the pulley by sliding it.
- While holding the belt, you need to rotate the pulley. This will help release the rubber or polyurethane part.
- Use a flashlight to illuminate the area where you are working to see if any parts of the belt remain un-removed if it has become frayed due to wear. If they are detected, it is necessary to remove all fragments so that they do not interfere with normal operation in the future.
- Place the new part onto the engine pulley. If you have to work through the top of the machine, you can use the help of a second person to grab the belt through the bottom. Or help yourself hook it by lowering it on a wire loop.
- After the part is draped over the engine, you need to pull it onto the pulley grooves. This must be done by holding the belt itself taut and turning the pulley clockwise.
- To make sure that the belt is “sat” in place, rotate the pulley.
- Reassemble the washing machine in reverse order.
- Run a test wash.
How to change the belt on an Indesit washing machine
Buy a strap from a manufacturer from a reliable supplier. Then completely remove the old element and its remains. Any belt has a cord that, when broken, unravels and winds around the device’s motor or nearby wires.
The new element must be placed on the engine and its upper part pressed tightly against the pulley. You need to simultaneously spin the drum while pulling the completely new element onto the pulley.
The strap should be positioned strictly in the center of the pulley, which is located on top. This can be done by moving the belt 2 tracks on the pulley at the bottom of the equipment. After which you can start the device for washing clothes.
How to choose, how much to pay and where to buy?
The best option is to replace the belt with an original one that fully matches all the parameters of the washing machine. You should choose a part taking into account the characteristics of your washing machine, so you can simply remove the worn one and buy exactly the same one .
Poly V-belts, which are not smooth on the inside and have a textured surface of several wedges, have proven themselves to work well.
An important parameter for poly-V belts is the distance between the wedges. For Samsung, the “J” type works well, which means a distance of 2.34 mm. This parameter is indicated on the part itself.
Near the letter on the surface itself the number of wedges is indicated . There can be up to 5 of them. J3 is suitable for narrow Samsung devices, and J5 for wide ones.
The length of the belt is also indicated directly on it. This is an important parameter that cannot be ignored, because otherwise the part will not fit the machine.
For Samsung cars - 1270. Thus, the marking 1270 J3 indicates a poly-V-ribbed three-ribbed belt with J-type wedges and a total length of 1270.
Belts are made from rubber and polyurethane. It is even possible to determine the type of material visually: rubber ones are black, polyurethane ones are light . The former have a longer service life.
A good three-ribbed belt 127 cm Megadyne (made in Italy) costs from 420 rubles. One of the cheaper options is also suitable, which can be ordered, for example, on Yandex.Market or bought in a specialized store.
Prices for simpler product options start from 200 rubles. They are inferior in quality and less durable, but gain in price. A wider belt has better grip and is less likely to slip.
Calling a specialist: the price of the issue
If it is impossible to replace the drive belt yourself, you must call a technician from a company that repairs household appliances. You can find a company on the Internet. A professional technician will do all the work, conduct diagnostics and give recommendations .
On average, the cost of replacing a belt will be up to 1,000 rubles. The new part itself is paid separately.
When calling a specialist to replace a belt, you must indicate the make of the machine, as well as whether a new part is available or the technician needs to bring it with him. If the technician additionally has to fix other faults, the amount will be higher.
For machines that are still under warranty, you should call a specialist only from the service center . All information about such companies must be in the documents for the washing machine.
Contacting specialists through private advertisements can be dangerous, since there is a significant chance of ending up with unscrupulous workers, weak specialists or simply scammers. Contacting a company that has been in the service provision market for a long time will help eliminate the risk.
All the most important and useful information about repairing Samsung washing machines is in this section.
How to call a specialist
You can call a RemBytTech specialist in any convenient way - by filling out the form on the website or by phone from 8.00 to 22.00:
READ MORE: Surge filter for a washing machine ✅: how to check what it’s for
When contacting, please inform the manager:
- The brand of the washing machine, if you only need to install the belt (if it has fallen off or if you have already bought a new part yourself). If you need to replace a drive belt that has become unusable, please also tell us the model of the unit. For example, Samsung S821, Electrolux EWS 1105 or LG WD-8012C. The exact number can be found on the body of the washing machine on a special tag or in the operating instructions. This information will allow the technician to take with him the “original” belt installed on your unit by the manufacturer for replacement work.
- The day and time of arrival of the master that suits you.
- Contact information – your last name, first name, address and telephone number.
On the selected day, the technician will call you again to confirm a time convenient for you to replace the belt.
