Error F 08 in the Ariston washing machine

  1. Information
  2. Washing machines
  3. Error codes
  4. Ariston
  5. F06

As usual, you put the laundry in the drum of the Ariston or Hotpoint-Ariston washing machine, selected the program and started the wash. But the machine never started washing, perhaps without even drawing water, and the display showed error code F6 or F06.

However, you could have discovered the error at the end of the wash, when the Hotpoint-Ariston washing machine completed the program, but did not open the door, issuing code F06 a few minutes after the end of the program. In rare cases, this error:

  • occurs at any time during the washing, rinsing or spinning cycle;
  • it appears at any time during the program execution, then the machine washes normally.

If you have an Ariston washing machine without a screen, then it will signal error F06 by flashing certain indicators. Which ones? Depends on model:

  • On the oldest models, with two indicators - power and hatch lock (Ariston Margherita type), the power indicator (Network) will blink 6 times with a break of 5-10 seconds. In this case, the program selector knob will rotate clockwise and make clicks.
  • In Hotpoint-Ariston models of the Low-End line (ARSL, ARXL, AVM, etc.), the “End of program” (End) and “Drain” lights (respectively, the second and third from the bottom in the vertical row of indicators that show the current stage of the program) will blink ). All additional function button indicators may also light up: in some models they are located horizontally on the control panel, for example, Hotpoint-Ariston BHWD, BHWM, ARTL, ARUSL, etc., and in some - vertically (models ARTF, AVC, ECOTF and other).
  • In Hotpoint-Ariston Aqualtis washing machines without a screen (models AQSL, AQ9L, AQS0L, etc.), error F 06 will be indicated by flashing temperature indicators of 30°C and 40°C (the second and third temperature light from the bottom, respectively).

Error interpretation

Error F06 or F6 is displayed only on Hotpoint-Ariston washing machines with an electronic controller on the Arcadia platform (all models of the Low-End line, the Aqualtis series and some others) and on Ariston models of the Dialogic series (starting with AD, ALD, AXD and some others) . And means:

  • Problems in the UBL (hatch locking device) circuit in models with an Arcadia control module.
  • Problems with control buttons or program selector for Dalogic series machines.

Testing faults

We will be able to check all the functions of the Ariston machine, find the fault and even understand how to fix error F06. To do this you need:

  • take the SAT diagnostic key with coding 95 669;
  • connect it to the connector located on the rear panel of the machine;
  • if the Ariston unit has a drying mode, the key will light up with a green light. There are models on which the blue indicator lights up.

Remember that during testing the water temperature will increase by thirty degrees. So before checking you should set a certain mode. In addition, the Ariston washing machine is connected to the water supply network, the tank must be empty, and the door must be tightly closed.

To establish error F06 or other failure, you should turn on the Ariston washing machine, press the “Auto-Test” button and hold it. In this case, the scoreboard is monitored. If the test has started, “Test” will light up on the screen. In this case, a machine without a screen will emit a characteristic signal.

Error F06 - what to do and when you can fix it yourself

The appearance of code F 06 / F 6 on an Ariston washing machine is not always associated with a serious malfunction. Before calling a professional repairman, try to fix the problem yourself by following the tips below.

Hotpoint-Ariston models with Arcadia moduleAriston Dialogic series models
The washing machine door is not closed tightly. Something has gotten between the body of the washing machine and the hatch that is preventing it from closing. Or, due to your own carelessness, you did not close the hatch tightly. In order for the machine to start washing, you must close the door until it clicks. Buttons on the control panel stick or don't work. The button gets stuck or the contact in it disappears. Try clicking the button (on-off) several times, perhaps the error will disappear.
The contacts in the UBL circuit have come loose. Check all connections in the area from the washing machine door lock device to the control board. Perhaps due to vibrations during operation, some connector in the UBL circuit came loose, and therefore the machine shows error F 06. The control button connector is not connected tightly to the electronic controller . Check the buttons and restore tight contact if necessary.
Failure of the control module (electronic controller) or indication. If the error appears for the first time, try rebooting the Ariston SMA by unplugging the plug from the outlet for 5 - 10 minutes. It happens that control or display modules malfunction, and after a reboot the error will disappear. The cause of the failure may be high humidity in the room where the washing machine is used.

If these recommendations did not help get rid of error F06 on your Ariston SM, then most likely a breakdown has occurred. In this case, unfortunately, you cannot do without professional knowledge and repair experience. You will need the help of a specialist.

Problems that do not require repair

The contacts of the heating element have been sent

The cause of the problem may be poor electrical contact. Three wires are connected to the heating element, each of them is connected to the heating element by a connector. If at least one of the contacts becomes loose, loose or falls off, this will cause the machine to fail.

To resolve this problem, first of all, you need to disconnect the power cable from the network. Then remove the back panel of the machine, behind which the contact terminals of the heating element are located and carefully fix the loose connector. After this, replace the removed cover and check the operation of the unit.

Control board failure

To restore normal operation, sometimes it is enough to reboot the control system. It is necessary to remove the cable plug from the socket for some time (5-10 minutes). If the cause of the problem is a failure of the control module, normal operation will resume after switching on again.

High indoor humidity

Installing a washing machine in rooms with high humidity has a negative impact on many of its elements. Traces of corrosion may appear on the housing, and condensation formed on the electrical contacts will lead to operational errors.

To avoid such problems, the machine should be installed in a dry, ventilated area with adequate ventilation. Bathrooms tend to have high moisture content and are more likely to cause problems. Therefore, it is better to install the unit in other rooms, for example, in the kitchen or pantry.

Possible faults requiring repair

RemTytTech specialists have already repaired a total of 6,014 (!) washing machines of the Ariston and Hotpoint Ariston brands. Therefore, it was not difficult for us to group the most common breakdowns that lead to error F06 / F6 into tables.

Hotpoint-Ariston models with electronic controller on the Arcadia platform (starts with AQSL, AQ9L, AQ0L, ARTF, ARTL, AVM, ARUSL, ARSL, AVC, BHWD, AQSD, ARXL, AQ8F, AQ9F and many others)

SignsProbable CauseRepair or replacementCost* (work only)
The washing machine does not lock the door and the wash does not start. A few minutes after switching on, error F 6 or F 06 is displayed. The hatch locking device (UBL) has failed . Due to its breakdown, the machine door does not close or, conversely, does not unlock. The UBL needs to be replaced.from 1400 rub.
After the end of the program, the Ariston machine does not open, and the UBL error code is displayed.
Interrupts a program during a wash, rinse or spin cycle.
The washing machine does not start the program and writes code F 06. In some cases, the program may run as usual, but then is interrupted (in the wash, rinse or spin mode) by this error.The board is faulty (electronic controller) is the main microcircuit that controls the operation of the entire washing machine. The radio elements on the board in the UBL control circuit have failed. Most often, these are triacs, resistors, diodes, varistors, etc. Sometimes the tracks along which the signal is transmitted burn out, or the contacts of radio elements burn out. Infrequently, the UBL error can also be caused by:
  • controller firmware failure;
  • failure of the board processor.
All elements of the electronic controller in the UBL control circuit are tested with a multimeter and replaced if a malfunction is detected. Burnt contacts and burnt tracks are restored. If the firmware fails, the controller is re-flashed. If it is not possible to restore the module using the above manipulations or it immediately becomes clear that the problem is in the processor, then the controller is replaced with a new one. from 2000 rub.
After starting the wash, the hatch of the Hotpoint-Ariston washing machine closes, but does not lock. Water is not being collected. After 1-2 minutes, code F 06 lights up. Mechanical damage to the washing machine lock (including the hatch tongue). Most often, it occurs as a result of careless use or children's games with the washing machine. As a rule, the manufacturer does not provide repair kits for the lock, and you have to change it completely.from 1400 rub.
There may be a wide range of signs from the machine refusing to start washing, as in previous breakdowns, to the program being interrupted during execution.Damaged wiring or contacts in the area from the electronic controller to the hatch locking device. Because of this, the signal in the UBL control circuit breaks and an error occurs. In private homes, damage is often caused by mice or rats. Damaged wiring is restored or the cable with wires is completely replaced. The contacts are carefully soldered or replaced with a new contact group. from 1600 rub.

*Price without parts, spare parts are paid separately. The exact amount depends on the Ariston washing machine model and is determined by the technician after diagnosis.

Ariston Dialogic series models (starting with AD, ALD, ALDS, ATD, AXD and others)

SignsProbable CauseRepair or replacementCost* (work only)
The washing machine does not start in any program, this error code blinks. Sometimes the machine may not work only on certain programs. The program selector is faulty.The selector needs to be repaired or replaced.from 2100 rub.
The Ariston washing machine does not turn on the wash, and error F06 flashes. on the control panel have failed As a rule, this occurs due to mechanical effects on the buttons. You press them carelessly, the buttons stop working or, conversely, become stuck. As a result, the contact in them disappears or, on the contrary, appears at an unnecessary moment, and an error is indicated. Damaged control buttons need to be replaced.from 1100 rub. (one button)
Control module is faulty (electronic controller) is a microcircuit that controls the operation of the entire machine. The radio elements on the module responsible for receiving signals from the control panel (CND connector) have failed. Sometimes the traces of the microcircuit through which the signal is transmitted burn out, or the contacts of radio elements burn out. It happens that the error occurs due to:
  • controller firmware failure;
  • failure of the microcircuit processor.
All radio elements of the electronic controller responsible for receiving signals from the control panel are checked with a multimeter and replaced if a malfunction is detected. Burnt out tracks and burnt out contact groups are restored. If the firmware fails, the controller is reprogrammed again. If it was not possible to restore the module using the indicated methods, or during diagnostics it is immediately clear that the problem is in the processor, then the controller is replaced with a new one. from 2000 rub.
Most often, the machine refuses to start the wash, but it happens that the program is interrupted during execution. from the control buttons to the electronic controller or the contact groups are damaged .The wiring is restored or the cable with wires is completely replaced. The contact group of buttons is soldered or also replaced with a new one. from 1600 rub.

* The price is for labor only, spare parts are paid separately. The exact price depends on the Ariston washing machine model and is determined by a specialist after diagnosis.

If you yourself could not cope with error F6 / F06 on an Ariston or Hotpoint-Ariston washing machine, call the RemBytTech specialist by phone:

+7 (495) 215 – 14 – 41

+7 (903) 722 – 17 – 03

or using an application on the website.

We work daily from 8 am to 10 pm, excluding holidays and weekends, so you can easily find a time convenient for repairs. After contacting, a specialist will come to you within 24 hours, find out the cause of the problem and, if necessary, carry out repairs right at your home. After elimination, you will be provided with a warranty for up to 2 years .

Rate this article: 4.5 1 5 22 votes (average 4.5 based on 22 votes)

What to do

If the Ariston machine has generated an error code f01 by indicating or displaying the value f01, then initially it is necessary, to exclude the possibility of simple malfunctions, to perform the following steps:

  1. Disconnect the household appliance from the power supply. As a result of this, the previous mode will be reset, and the machine should start working. It happens that the cause of periodic failures of Ariston electronics, such as error f01, is high humidity in the room where it is located.
  2. Check the voltage in the network for surges. If it is determined that the voltage is less than 220 V, then you need to try to eliminate the interruptions or connect a voltage stabilizer.
  3. Examine the power cable from the outlet to the machine for possible damage, pinched areas, or failure of the connection plug. If found, the element must be replaced.
  4. Examine the connecting contacts between the motor and the board, because contacts may have come loose in the motor control circuit. If you have skills in working with electronics, you can check the circuit from the motor to the board yourself, ringing all areas that are in doubt.

If, after performing the described steps, error f1 on the Ariston washing machine continues to appear, then you need to continue studying, but this time the internal part. To do this, install the machine in the center of the room so that it can be approached from different sides, unscrew the back cover, disconnect the wires from the engine and remove it.

After this, you need to inspect the brushes, study the winding, and if there is no breakdown, then further actions concern studying the electronic board.

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]