Causes
It will not be possible to immediately determine why the washing machine stopped turning on. This requires an inspection of the equipment. In this case, attention should be paid to both the external elements of the device and the internal ones. For example, the main reasons for lack of performance are:
- Electrical problems. This includes malfunctions of machines, sockets, extension cords.
- The power cord or plug is deformed.
- Overheating of the FPS - network capacitor.
- Door lock malfunction.
- Overheating of the start button contacts.
- Also, the cause of the breakdown may be a failure of the control module.
Most masters call the first two reasons “childish”, and indeed, solving them will not be difficult.
However, many housewives, falling into a panic, cannot soberly assess the situation; for them, such a malfunction is considered quite serious. The following three reasons will require a thorough inspection and immediate repair. For example, as a result of a door malfunction, the indicators may not light up; they can be replaced fairly quickly.
And finally, the last reason is the most multifaceted and serious. It is worth considering each of the cases separately.
Minor damage
In a situation where Ardo refuses to turn on, it is necessary to inspect the equipment for possible damage or malfunctions. You need to start with the simplest reasons, which are located under points 1 and 2 above.
The washing machine remains in place during the inspection. First of all, if the Ardo machine refuses to turn on, you will need to perform the following steps.
- Check the outlet. To do this, you need to remove the plug from the socket and connect another electrical device to it. The verification method is quite simple. The socket is considered broken if the connected device refuses to turn on.
- If the outlet works, you need to check the extension cord where the cord of the Ardo machine goes. The verification method is the same as above.
- The next element of inspection will be the network cable. If damage to the insulating layer is detected, and traces of melting are also noticed, the cord must be replaced. Its further operation is impossible. Otherwise, this may cause the Ardo machine to stop turning on and working.
- Finally, if you cannot see any damage, you can check the wire using a multimeter. To do this, you must first set the device to the minimum resistance value, and then touch the probe to one of the teeth (usually the right one) of the fork. The standard resistance value for an Ardo machine is 2 ohms. Any deviation indicates that the plug needs to be replaced.
It is also worth noting that if defects are detected in the network cable, it is not recommended to repair it yourself. It is better to take the help of professionals who can assess the damage and also take all the necessary actions so that the Ardo machine starts turning on again. For example, workers can easily replace the wire insulation or change the plug.
The washing machine rattles when washing
To replace these parts, the machine must be completely disassembled and the drum removed from the tank.
In the absence of a puller, the axle shaft can be knocked out of the bearing with careful blows of a hammer, but you need to hit not on the axle shaft itself (this can damage the threads), but on a placed board. The bearing itself can be knocked out of the cover using a blunt chisel and hammer. The blows must be applied evenly so that the bearing does not warp.
New bearings must be lubricated with lithol before pressing. Let us note once again that if you have no experience in metalworking, you should not take on this almost jewelry task.
Mains capacitor fault
Sometimes the washing machine may not turn on due to problems with the FPS. This abbreviation stands for interference filter or network capacitor.
The element is a semiconductor structure that is installed inside the washing machine to absorb minor interference. It is no secret that the operation of almost all electrical networks occurs with periodic interruptions. They are caused by the same interference, the effect of which on the washing machine is eliminated by the FPS. This ensures reliable operation of the equipment and all elements.
You can find the FPS at the end of the power cord if you look inside the Ardo washing machine. If the filter breaks, it will need to be replaced. This action can only be performed after the top cover of the machine has been removed.
To remove it, you will need to unscrew two bolts and pull the part towards you. Under the cover you will find a wire, as well as a capacitor. It is recommended to disconnect all connected wires from the capacitor and take the structure outside.
The filter's performance is also checked using a multimeter at minimum resistance values. The serviceability of the element can be indicated if the device shows a rapid increase in the indicator to one. If during the test the numbers 1 or 0 appear immediately, the capacitor must be replaced.
To replace, you will need to buy a new filter and install it in place of the old one. All the necessary wires are connected to the new capacitor, and then the cover is screwed back on.
If the cause of the problem with the washing machine was the capacitor, then after replacing it, the device will work properly as soon as it is plugged in.
Ardo washing machine does not drain water
The solution to the problem must be sought in the following sequence:
- It is necessary to check for kinks or twists in the drain hose.
- If the drain hose is connected directly to a sewer pipe (fixed connection), you must ensure that it is not clogged. The easiest way is to disconnect the hose and see if water flows out of it. If not, check the hose for blockages.
- If everything is in order with the sewer and drain hose, you should check the condition of the drain filter. It is made in the form of a threaded plug and is located at the bottom of the unit on the front side - behind the door or decorative panel. Before unscrewing the filter, place a container under the machine to collect water. It is necessary to clean not only the filter itself from debris, but also the place where it is installed. After this, you can screw the part into place and check the results of the work.
- The next suspect (if all else fails) is the drain pump. Most often, this unit breaks due to small objects getting inside - coins, buttons, etc. The pump is installed at the bottom and is easiest to reach by tilting the car on its side. Some models of Ardo washing machines are not closed at the bottom; others have an easily removable protective cover in this place. First, use a multimeter to check the presence of voltage at the pump contacts. If everything is in order with the electrical circuit, turn off the power to the machine and disconnect the pump.
The clamps holding the drain hose and pipe from the machine tank do not need to be completely removed - just loosen them slightly. Then the wires are disconnected and the pump itself is unscrewed. After removing foreign objects, the assembly is assembled in the reverse order.
Washing machine drain pump
If the pump turns out to be serviceable, we move on to the last link in the chain - the level sensor, also called a pressure switch. It is he who sends a signal to the controller about the need to start the drain pump. To get to this element, just remove the top cover of the machine by unscrewing the screws and slightly pushing it back. Next, you need to check the condition of the connections of the wires to the sensor contacts. If there are no complaints about them, the pressure switch should be dismantled and the tube connected to it from below should be inspected for blockages.
Next, you need to blow into the tube - this way the functionality of the device is checked. If it is in working order, you should hear a click. If you cannot hear any clicks, you need to purchase and install a new level sensor.
There is no reason to complain about the quality of Zanussi washing machines, but no one is immune from unpleasant surprises. Zanussi washing machine - do-it-yourself repair of the mechanical component of the unit.
You will learn how to fix some types of failures of Indesit washing machines here.
It doesn’t always make sense to contact specialists if your washing machine breaks down. Some problems can be fixed on your own. If you are the owner of a Kandi washing machine, the following article https://aquacomm.ru/cancliz/mnogokvartirnyie-doma/santehnika/kandi-stiralnaya-mashina-remont-svoimi-rukami.html will help you deal with its repair.
Damage to the device power button
Another option why the Ardo washing machine does not turn on is a malfunction of the power button. Often the problem arises because the equipment is already old. Also among the most popular reasons are:
- Contact wear. In this case, the breakdown occurs gradually. At first, the indicators light up periodically, and then completely stop responding to any action.
- Water ingress. Liquid can penetrate inside the button, causing overheating of the electrical circuit responsible for the operation of this element.
- Oxidation of contacts. The problem occurs as a result of excess moisture. Therefore, it is worth paying special attention to such a moment.
In order to repair the button, you must first remove the control panel of the washing machine. To do this you will need:
- Remove the top cover by unscrewing all nuts and bolts.
- Inspect the button contacts and check their functionality using a multimeter. The check is carried out in exactly the same way as described earlier. In this case, you should also pay attention to the appearance of the numbers 1 or 0.
- Remove the button if any defect is found. Most cases require the use of a soldering iron.
- Install a new button in the same place.
- Put the lid back on.
- Plug in the washing machine.
If the power button lights up, the problem is resolved.
Hard case
Finally, if during all previous checks it turned out that all the inspected elements are intact, it is worth concluding that the problem lies in the control module.
This type of malfunction is considered the most serious in the case of the Ardo washing machine. And it is not recommended to replace this element yourself. The work must be performed by an experienced specialist who can not only determine the extent of the damage, but also replace the part or element.
It is worth noting that one of the options for repairing the control module is replacing the microcircuit. And you can perform this action yourself only if you have experience working with such electronics. And even in this situation, the probability of success is much less than in the case of a professional.
The operation of any equipment requires a responsible and careful attitude, and the Ardo machine is no exception. If the device stops turning on or malfunctions, you should carefully inspect it for possible damage to various systems.
Timely detection of a breakdown and replacement of a part will allow you to avoid more serious problems. If necessary, if the equipment stops turning on, you can turn to professionals for help.
What do we offer
Ardo washing machine does not want to start?
Call the Rewasher service center and call a technician. A specialist arrives shortly after submitting an application, conducts free diagnostics, eliminates the malfunction and issues a warranty card for spare parts and work performed. The technician will also give recommendations on further operation of the equipment. To call a service center specialist, you can leave a request on our website or call the operators at the indicated numbers. We'll get your machine back up and running in no time!
