LE error on a Samsung washing machine: what it means and how to fix it

What to do if an error code appears on the display

So, the LE error in Samsung machines means spontaneous draining of water from the unit’s tank. There are several reasons for such a breakdown:

The drain hose is not installed correctly.
The connection of the hose to the sewerage system is broken.
Damage to the water drain tank (crack, loose bolts).
The drain filter is not completely closed.
The air tube is disconnected, causing water to leak during the spin cycle.
There is a malfunction in the water level sensor.
The operation of the indicator itself is disrupted.

What is it and what does it mean?

The Samsung washing machine is equipped with a microcomputer that controls all stages of washing. When unexpected processes occur, a certain symbol begins to flash on the screen.

Code le means that the problem is related to the low water level in the drum during the automated washing process.

This could be either a leak or self-draining. The sensor is triggered if, within a few minutes, it detects a decrease in the water level in the tank of the machine four times in a row.

Often, simultaneously with the display blinking, a puddle of water is detected on the floor next to the machine. The time at which the defect occurs may vary.

It often occurs:

a few seconds after starting the wash;
almost immediately after filling the tank with water;
during the washing or rinsing process.

The problem associated with water leakage can be indicated on the display not only in the form of the designation le, but also other codes: e9, lc, le1.
Differences in error encryption are associated with the design features of Samsung machines and the year of their manufacture. Thus, washing units manufactured before 2007 are programmed with the designation e9. More modern models have the letter code le.

If the washing machine is not equipped with a display, then this error can also be easily identified . If water is drained unplanned by the program, the unit signals by flashing indicators.

If an error occurs, two icons glow steadily red: “Bio 60°C” and “cold water”. All washing mode indicators flash at the same time.

Deciphering the codes

Errors in a Samsung washing machine can be indicated differently, but indicate the same problem - water leakage from the tank. Depending on the year of manufacture of the model of this brand, codes LE, LC, E9, LE1 may appear on the screen. The E9 code, for example, was used by the manufacturer in early models of washing machines, until about 2007.

The design of the machines includes a pressure switch, or water level sensor. If the sensor detects a drop in water level below the established norm 4 times in a row, one of the listed error codes will appear on the display.

Decoding

The LE code alerts the user to a self-draining or water leak. The device that records this process is called a pressure switch. This is a sensor that analyzes the water level in the tank. Each washing program has its own water level. If the water drops below the required level, the machine displays an LE error.

Some washing machines have an “Aquastop” system, which includes a float sensor. If an error occurs, the sensor pops up and the machine is blocked.

If you have a machine older than 2007, you will see the abbreviation E9 on the panel. Other error codes for a similar problem may be LC and LE1.

The LGI model washing machine shows a similar code - 1E or IE.

Procedure for detecting a failure

An error may appear on the indicator both at the beginning of the wash and during the rinsing or spinning process. To troubleshoot the problem in time and bring your washing machine back to life, follow the following steps.

Disconnect the machine from the power supply by unplugging the cord from the outlet. Press the off button on the washing machine.
Carefully inspect the drain hose - there should be no cracks or breaks on it. Check its position, integrity and connection to the sewer thoroughly.
If the position of the drain hose is incorrect, connect one end to the bottom of the machine, and point the other upward, attaching it to a special hook. The connection of the hose to the drain pipe must have a good seal and be located at a distance from the floor of at least 70 cm.
Consider the drain filter device. To open the lid, turn it counterclockwise; to close it, you need to move the lid clockwise. If the cap is firmly attached and covers the drain hole, then the problem is not with the filter.
When a fault cannot be identified with the naked eye, it is better to contact service. It is likely that the failure is internal to the machine. For example, a tubular electric heater (TEH) broke, a crack appeared in the tank, or another part failed. Qualified specialists will examine the cause of the error and, if necessary, replace the failed part.

If this is the first time the error code has appeared, unplug the machine for a few minutes. Perhaps the reason lies in the failure of the control module, and to resume proper functioning you simply need to reboot the equipment.

How to fix the problem

Before resuscitating the machine, press the power button. Disconnect the device from the network. If an error occurs and the machine is working properly, a simple reboot will help. Leave the SMA alone for 10 minutes and turn it on again. The cause of it all was the control module. A power outage can also cause the wash program to fail.

If this doesn't help:

Contact the service center if the machine has warranty time remaining. Some parts and mechanisms should not be changed manually; it is better to entrust this to professionals. They will select a suitable replacement rubber housing or hose and replace it free of charge. It is worth contacting repairmen in case of a crack in the drum, pan or housing.
You can replace the drain hose yourself or from the pump to the drum. Bring the broken part to the store, they will find the same one for you.
If the drain hose is placed far down the riser, set it to the proper height. Most Samsung models have a small plastic loop with which you can attach the drain hose to the desired level. The fastening must be located at a distance from the floor of at least 70 cm.
If the wash started, but instead of drawing water, the device generated an error, replace the float sensor (for models with aquastop). For a Samsung washing machine with a water level relay (pressostat), blow out the tube; perhaps the reason was that it was clogged. In case of malfunction, a replacement must be made.
The error occurred during washing without visible damage - resolder the board or replace the microcircuit at a service center.
An incorrectly connected hose to the sewer can cause the L9 value.

After eliminating the causes, the indicator may light up again. Poor contact with the electrical network may contribute to this. Change the wiring, twist the wires or replace the cable with a new one.

You can fix some LE errors in your Samsung washing machine yourself. Drum failure or soldering of microcircuits requires professional knowledge and experience in troubleshooting such problems. Call a diagnostic specialist to solve problems or use warranty service.

What other errors could there be?

Not only the LE code tells us about violations associated with self-draining of water. It happens that dirty water does not drain from the tank at all. Then code 5E lights up on the display. This, in turn, is associated with a clogged drain hose or filter, or with a malfunction of the drain pump. It is quite possible to repair the drain pump yourself.

Error 5d also refers to water leaking out, but this time along with soap suds. The reason for increased foam formation may be the wrong choice of washing powder (for example, intended only for hand washing) or exceeding its volume by one cycle. There is no need to deal with this problem: after some time, the foam will settle on its own and be removed, and the washing process will start again. But for the future, remember that only specialized products with appropriate markings are recommended for automatic machines.

Never use hand washing powders: they will not only ruin your clothes, but can also cause damage inside the machine itself, which is much more serious.

What to do if an LE error occurs on a Samsung washing machine

New generation washing machines are designed in such a way that they themselves inform us about a malfunction. Imagine: you decided to wash your clothes, loaded them into the drum, set the desired program and suddenly discovered an impressive puddle of water on the floor. And on a Samsung washing machine, the error LE, LE1, LEC or E9 was displayed. If you understand the meanings of these codes, you can understand the essence of the problem.

What to do if an error code appears on the display

So, the LE error in Samsung machines means spontaneous draining of water from the unit’s tank. There are several reasons for such a breakdown:

The drain hose is not installed correctly.
The connection of the hose to the sewerage system is broken.
Damage to the water drain tank (crack, loose bolts).
The drain filter is not completely closed.
The air tube is disconnected, causing water to leak during the spin cycle.
There is a malfunction in the water level sensor.
The operation of the indicator itself is disrupted.

Deciphering the codes

The design of the machines includes a pressure switch, or water level sensor. If the sensor detects a drop in water level below the established norm 4 times in a row, one of the listed error codes will appear on the display.

Procedure for detecting a failure

Disconnect the machine from the power supply by unplugging the cord from the outlet. Press the off button on the washing machine.
Carefully inspect the drain hose - there should be no cracks or breaks on it. Check its position, integrity and connection to the sewer thoroughly.
If the position of the drain hose is incorrect, connect one end to the bottom of the machine, and point the other upward, attaching it to a special hook. The connection of the hose to the drain pipe must have a good seal and be located at a distance from the floor of at least 70 cm.
Consider the drain filter device. To open the lid, turn it counterclockwise; to close it, you need to move the lid clockwise. If the cap is firmly attached and covers the drain hole, then the problem is not with the filter.
When a fault cannot be identified with the naked eye, it is better to contact service. It is likely that the failure is internal to the machine. For example, a tubular electric heater (TEH) broke, a crack appeared in the tank, or another part failed. Qualified specialists will examine the cause of the error and, if necessary, replace the failed part.

If this is the first time the error code has appeared, unplug the machine for a few minutes. Perhaps the reason lies in the failure of the control module, and to resume proper functioning you simply need to reboot the equipment.

What other errors could there be?

Never use hand washing powders: they will not only ruin your clothes, but can also cause damage inside the machine itself, which is much more serious.

Conclusion

Remember that spontaneous draining of water is a rather serious operating error of the machine. After all, you can easily flood your neighbors below if you don’t pay attention to the problem in time. Manufacturers of modern Samsung models have made our task much easier by providing codes on the display. Knowing the decoding of a particular code, you can fix the problem yourself. Just approach the solution of the problem responsibly, weigh your strengths: can you fix the problem yourself? If not, then it is better to seek help from professionals who will carry out repairs and give advice on how to avoid repeated water leaks in the future.

LE error in Samsung washing machine - Samsung

Most often, a washing machine breakdown occurs at the most inopportune moment, so let’s figure out whether it’s worth sending the machine in for repair right away or whether you can fix the problem yourself. There are many codes (errors) in washing machines, all of them are designed to indicate to us that there is a breakdown or that it will happen soon. In this topic we will talk about the LE error in a Samsung washing machine.

Error LE means a sharp decrease in the water level in the machine drum - there is a spontaneous leak; when the water level is critical, the washing automatically stops to avoid overheating of the heating element.

Main causes of LE error

Incorrect position and fastening of the drain hose;
Damage to the tank (cracks, holes);
Cracks and punctures in the drain hose;
Air tube disconnection;
Incorrect operation of the drain filter;
The heating element has a faulty fastening;
Drain hose extension;
Poor quality detergents, large amounts of powder;
The powder tray is clogged;
The pan filled with water and the float reacted (for models with aquastop).

Troubleshooting LE error

How to resolve the LE error in a Samsung washing machine:

Disconnect the washing machine from the power supply - press the On/Off button, then unplug it from the outlet.
Check the drain hose, it must be attached to a special mount from the manufacturer and take the shape of a hook or an oval, first the hose must be lifted up, then bent, and then only down to the sewer drain pipe, the other end of the hose is fixed at the bottom of the machine.
If you have extended the hose, then check the attachment point with the factory hose, perhaps this is where the leak is occurring, it is better to disconnect the extension for a while, then place the hose in the bathroom or sink until the cause of the leak is determined.
You also need to check the hose for integrity, whether there is any damage due to which the LE error appeared; if there is any, then only replacing the drain hose will help. It should also be taken into account that if the drain hose does not make an upper loop, and the sewer hole is below the tank, then the water simply leaves the machine, so you need to install the washing machine strictly according to the instructions or use the services of a professional.
Check the drain filter; its lid should be pressed tightly and not allow water to pass through.
If the LE error appears for the first time, and there are no apparent reasons for its appearance, then try to “reboot” the machine and let it “rest” for 10 minutes, and then turn it on again; perhaps there was a failure in the program.
If the appearance of this error is accompanied by the appearance of foam, then either the powder is not intended for automatic washing, or you put in too much quantity, rinse the powder tray and at the same time check the dispenser, remove blockages and use high-quality powder.
Check the tubes, hoses, connections, something may have become disconnected, which led to a leak into the sump and a reaction of the float, correct them (for Samsung models with the “aquastop” function).

Please note that the LE error in a Samsung washing machine in different models can be displayed as: E9, LE1, LC, and in models without a display, the Bio 60°C and cold wash mode lights are constantly on, while the lights for all modes are flashing.

If you have eliminated all the visible causes, followed these tips, and the machine still gives an error, then it is better to contact a specialist, as there may be more serious breakdowns that require special skills and knowledge to eliminate.

What does this error mean?

The LE error in a Samsung washing machine may indicate serious malfunctions such as:

Damage to the leakage sensor;
Damage to the tank from sharp objects or in places where it is bolted together;
The heating element has become detached from the mounting;
Faulty sealing washers;
The sealing cuff sank;
The reason is a wiring fault.

In these cases, it is better to immediately seek help from specialists and not aggravate the situation. In Yekaterinburg, many companies and craftsmen repair washing machines - you can’t make a mistake with your choice!

Sources: https://stiralkainfo.ru/remont/oshibka-le-na-stiralnoj-mashine-lg.html https://1stiralnaya.ru/neispravnosti/oshibka-le https://tehnika.expert/dlya-chistoty- i-poryadka/stiralnaya-mashina/oshibka-na-stiralnoj-mashine-samsung-le.html https://www.102mastera-ekb.ru/blog/oshibka-le-stiralnaya-mashina-samsung/ https://stiralkainfo .ru/remont/stiralnaya-mashina-lg-oshibka-oe.html

What to do if an LE error occurs on a Samsung washing machine

What to do if an error code appears on the display

So, the LE error in Samsung machines means spontaneous draining of water from the unit’s tank. There are several reasons for such a breakdown:

The drain hose is not installed correctly.
The connection of the hose to the sewerage system is broken.
Damage to the water drain tank (crack, loose bolts).
The drain filter is not completely closed.
The air tube is disconnected, causing water to leak during the spin cycle.
There is a malfunction in the water level sensor.
The operation of the indicator itself is disrupted.

Deciphering the codes

The design of the machines includes a pressure switch, or water level sensor. If the sensor detects a drop in water level below the established norm 4 times in a row, one of the listed error codes will appear on the display.

Procedure for detecting a failure

Disconnect the machine from the power supply by unplugging the cord from the outlet. Press the off button on the washing machine.
Carefully inspect the drain hose - there should be no cracks or breaks on it. Check its position, integrity and connection to the sewer thoroughly.
If the position of the drain hose is incorrect, connect one end to the bottom of the machine, and point the other upward, attaching it to a special hook. The connection of the hose to the drain pipe must have a good seal and be located at a distance from the floor of at least 70 cm.
Consider the drain filter device. To open the lid, turn it counterclockwise; to close it, you need to move the lid clockwise. If the cap is firmly attached and covers the drain hole, then the problem is not with the filter.
When a fault cannot be identified with the naked eye, it is better to contact service. It is likely that the failure is internal to the machine. For example, a tubular electric heater (TEH) broke, a crack appeared in the tank, or another part failed. Qualified specialists will examine the cause of the error and, if necessary, replace the failed part.

If this is the first time the error code has appeared, unplug the machine for a few minutes. Perhaps the reason lies in the failure of the control module, and to resume proper functioning you simply need to reboot the equipment.

What other errors could there be?

Never use hand washing powders: they will not only ruin your clothes, but can also cause damage inside the machine itself, which is much more serious.