During operation of the washing machine, sometimes an error situation may occur - error F01.
When it appears, the wash stops. To continue using your washing machine, it is important to correctly determine the cause of the failure and repair it.
What does error F01 mean on an Indesit washing machine and how to detect and fix the problem, we will tell you in the article.
Deciphering the F01 code for the Indesit washing machine
F01 - indicates a lack of voltage - a short circuit in the electrical circuit. This breakdown most often occurs when the motor wiring is worn out.
This problem is more typical for old equipment that has been in use for a long time or for a machine that has been used carelessly.
With F01, the signal from the control module is not transmitted to the drum, and the washing process does not occur. Without eliminating the cause of the failure, you will not be able to use the washing machine.
Causes and diagnosis
Even if the “F01” error occurred for the first time, it is necessary to carry out diagnostics and understand the cause of its occurrence.
The following circumstances may lead to malfunction:
voltage drops in the network;- breakage of the socket, plug or cord;
- physical wear of motor brushes;
- corrosion of electrical circuit contacts;
- malfunctions of the washing machine components;
- control board failure;
- turning the washing machine on and off during operation.
One of the possible causes of the failure is resetting the programmed settings. In this case, it is better to force a reboot of the machine:
- Disconnect the device from the electrical network.
- Leave for 30 minutes.
- Insert the plug into the socket.
- Start the machine.
If the reboot does not help, you will have to start troubleshooting, sequentially analyzing the operation of the nodes
There is a problem with the outlet, plug, or cord
Very often, the cause of the F01 code is an unstable voltage supply due to damage to the socket, cord or plug.
They need to be inspected, integrity checked and made sure there are no scorched areas indicating broken contact. In addition to a visual inspection, it is necessary to take measurements using a multimeter.
Mains voltage
Before you begin diagnosing a problem in the washing machine itself, you should check the voltage in the network . According to the rules, it should be 220V. It is this indicator that household appliances, including the Indesit washing machine, are designed for.
If the voltage in the network fluctuates, then the operation of the washing machine should be organized through a voltage stabilizer. This will extend the life of the equipment and reduce the likelihood of failure due to a short circuit.
Broken or stretched drive belt
The belt in the washing machine ensures that the drum rotates, which is provided by the motor.
If the belt has slipped, torn or stretched, it either does not perform its functions or performs it intermittently.
To verify the condition of the unit, you need to remove the back panel of the washing machine and gain access to the belt.
The worn part must be replaced with an identical one (all the necessary information is located directly on the belt itself) or, if it has simply fallen off, its correct location must be restored, paying attention to the grooves and pulley.
Engine problems
Access to the engine can be gained through the service hatch - it is located on the rear wall. You can check the engine's performance after removing the element.
To do this, perform the following steps:
- remove the back wall;
- remove the drive belt by loosening the pulley;
- carefully disconnect the wires leading to the engine;
- remove the engine.
When disconnecting wires from the engine, it is very important not to forget which ones are attached where. To avoid confusion, it is recommended to draw up a contact diagram before removing the part.
Diagnostic algorithm:
- Inspection of carbon brushes. Over long periods of use, these parts tend to wear out. When worn out, they should be replaced with new ones.
- Inspection of contacts. The problem can be caused by both dust and the smallest fractions of coal.
- Checking the motor winding. In addition to visual inspection, it is necessary to use a multimeter to determine the resistance; this indicator should be in the range from 20 to 200 Ohms.
- Inspection of the condition of the collector lamellas.
Corrosion of washing machine parts is not a rare situation. This is explained by the specific location and operation of the device itself - with the presence of moisture.
Metal elements, including the engine, are susceptible to corrosion. If the defects cannot be eliminated, the engine requires replacement .
Control module problems
The control module is the “brain” of the machine. This is one of the tricky parts. Some defects are noticeable to the naked eye and can even be eliminated on your own.
For example:
- condensation that has appeared and requires drying;
- dark spots - they can be wiped off with an alcohol-containing product.
It is best to entrust a specialist to carry out high-quality diagnostics and troubleshoot problems in this element, since correction requires not only special skills and knowledge, but also a suitable tool.
You can see how the module’s state is analyzed in the video:
How to fix the problem yourself
If error F1 occurs, first check the presence of voltage in the power supply. For normal operation, the Indesit washing machine requires a power supply of more than 200 V.
If the voltage is okay, reboot the system. To do this, unplug it for 20 minutes, then turn it back on.
What to do if error F 01 appears on the display again:
- Check that the outlet and cord are working properly.
- Is your external condition not suspicious? Then you need to inspect the engine:
- Open the service hatch. Using an 8 mm wrench, unscrew the electric motor and carefully disconnect the wires connecting it to the motor.
- After removing the engine, inspect the two plates (brushes).
- Remove them with a screwdriver and inspect them for damage and wear. If this is the reason, the brushes should be replaced with new ones. The next time you wash, you may hear a characteristic cracking sound. Everything is fine, the new brushes are being ground in.
- Check the control module contacts. They often corrode due to high humidity. If possible, clean or replace contacts.
- If the motor winding is burned out or worn out, the motor must be replaced. It happens that repairs are impossible or not profitable from a financial point of view. Then it is cheaper to buy a new car.
- A problem with the control module is not a task for beginners. This is one of the expensive and complex parts. Therefore, it is better to entrust repairs to a professional technician.
What does it mean that the drum stops during washing? Let's look at this problem separately.
You loaded the laundry, started drawing water, but at some stage the process stopped. At the same time, error F1 appears on the display. First of all, unplug the Indesit washing machine and drain the water using the drain valve. Empty the tank and try to figure out the problem.
Overload
First check if the drum rotates under your hand. If so, divide the laundry in half and run the wash again.
The washing drum does not work, but rotates by hand
Possible malfunctions and their solutions:
- Belt problems: broken, worn, loose, or slipped off the pulley. In the latter case, you need to return the belt to its original place, in the rest it should be replaced.
- Electronic board failure: the drum does not receive a start signal. To clear the error, you will need to reset the programs. In severe cases, re-flashing or replacement of the part is required.
- Erasing the brushes requires replacing them.
- Motor malfunction. As a result of frequent power surges and leaks, a serious breakdown occurs - only a specialist can fix this.
Call a specialist: price issue and quality guarantee
In cases where it was not possible to solve the problem on your own, and error F01 on the Indesit washing machine remains, you should contact a repair company . You can find such a company in your city using the Internet.
There you can also look for reviews about the company that repairs Indesit washing machines and check the prices. Additional questions, as well as calling a specialist directly, are indicated in the contact information on the company’s website.
The cost of services for repairing an Indesit washing machine is in a fairly wide range, differing not only by region, but also within one locality.
The price includes the cost only for the service provided. Parts that require replacement are paid separately, as are the consumables used.
Average cost of repair work in the capital:
- board repair – from 1,000 rubles;
- repair or replacement of the motor - from 1,500 rubles, etc.
Companies that operate officially on the market must provide a guarantee for the repairs performed.
Repair and replacement
- Check the electric motor windings for breaks (motor repair);
- Check the wear of the motor brushes (replace the brushes);
- The module ( triac is faulty - repair or replacement.
Other errors of INDESIT washing machines:
- F02 - Incorrect operation of the electric motor (engine)
- F03 - Temperature sensor malfunction
- F04 - Water level sensor malfunction
Rate this article: 4.2 1 5 56 votes (average 4.2 based on 56 votes)
Preventive measures
To prevent error F01 from appearing on the Indesit washing machine, you must adhere to the following preventive measures:
Avoid getting water on the machine from above, since the control module is located at the top.- It is important to control the voltage in the network. If it is not stable, then the washing machine should not be connected to the network without a voltage stabilizer.
- Do not unnecessarily turn off the machine during operation. Frequent switching on and off causes damage to electrical components.
- When unplugging the washing machine from the power supply, only grasp the plug. Pulling on the cord may damage the wire.
If the washing machine is malfunctioning, periodically producing errors and stopping operation, it must be sent for a routine inspection to a specialist.
Error F01 in the Indesit washing machine - how to fix it
This error does not appear on the display very often. Most often it occurs on older car models in which the display occurred in a different way. Error F01 on an Indesit washing machine refers to a situation where the washing machine motor is faulty. Such problems usually arise in washing machines that have been in use for a long time.
The electric motor is the main part of the washing machine. This unit is reliable and durable. Such failures are mostly associated with wear and tear of equipment.
Recommendations
When repairing an Indesit washing machine that displays error F01 on the display, the following tips will help:
- If an error occurs during the washing process, you must first unplug the machine, drain the water and remove the items from the drum. And only after that you can begin to search for the cause of the malfunction.
- If you independently identify the cause of the malfunction and cannot eliminate it, you should contact a specialist.
- When the brushes wear out, both should be replaced at once. They are selected based on the specific model of the washing machine.
- If the washing machine is partially disassembled and parts are removed, it is important not to lose the fasteners.
If an old Indesit machine requires replacement of the engine and other components, then repairs may not be profitable, and it will even be easier to buy a new washing machine than to restore the functionality of the old model.
Read about decoding error codes for Indesit washing machines in this section.
