How to connect tricolor to Thomson TV

The next step after installing the satellite dish is to connect it to the television receiver through the receiver, which is equipped with two types of outputs - analog and digital. The receiving device is designed to decipher received satellite signals, sometimes encoded, and further transmit them to a television receiver. The user is wondering how to connect the Tricolor receiver to the TV in the correct way. Since the tuner is the most expensive in the set of receiving equipment, when purchasing a device, it is recommended to carefully select a suitable set-top box, according to the recommendations on the company’s website.

Selecting the appropriate connector on the receiver

There is a power cord on the rear panel of the receiver, and there are also several connectors:

• HDMI. Working in this format for receiving information, any conversion of the video signal is excluded. The image is obtained in the same quality as the operator broadcasts. Tricolor TV is gradually abandoning the MPEG 2 and MPEG 4 formats, replacing them with higher quality HD, so HDMI is the best way to pair devices;
• analog RF. Previously widely used format. The antenna input receives analogue channels;
• component output. Transmits a high resolution signal. Each cable has its own color and is designed to transmit information corresponding to its color (brightness, red, blue and additional for audio channels). Before starting the connection, in order to avoid tangling the cables, you must read the instructions. The advantage of such a connection is clear image transmission;
• composite audio-video AV output. Known as "tulip". Found on almost every TV or satellite tuner. To connect yourself, you need to connect the multi-colored cable ends to the corresponding sockets on the receiver and television set. This connection is suitable for an old TV;
• SCART format. European connection standard that simultaneously transmits audio and video signals. It is the most used type of connection;
• S-Video format. A circular connector with several contacts inside. Similar to pairing a computer system unit with a keyboard or mouse. Occurs on more expensive equipment.

The tuner has connectors for connecting a high-frequency antenna cable and a converter - LNB OUT and LNB IN, respectively. Depending on the model of the installed device, there may be tulip, SCART, HDMI connectors. The satellite operator provides its customers with a wide range of receiver models, so the set of available outputs differs significantly. The receiver software is updated via the USB output.

Depending on the tuner firmware version, broadcasting occurs either to all available outputs, or only to certain ones. In view of this feature, the technical characteristics of the receiver and the methods of connecting it to the television receiver differ.

Connecting Tricolor TV to a TV: detailed instructions

Tricolor TV is installed when there is a desire to choose programs from more than a hundred channels. Thanks to the satellite dish, users receive high-definition images.

The plate is fixed on the roof of the building or the wall of the building. Additionally, a converter is installed; a tuner is needed for operation. The device is connected to the equipment. Users are often interested in how many TVs can be connected. If necessary, you can connect several devices to one antenna, for example, 4 pcs.

In order to watch TV channels, the receiver is connected to an antenna. To do this, use the holes located on the equipment.

Users are often interested in how to connect the Tricolor receiver to a TV.

There are different connection methods:

1. RF. This option was used when there were old TVs and, if necessary, installing an indoor or outdoor antenna.
2. AV. It can be found on all devices. Using a multi-colored cable, the receiver is connected to the old equipment.
3. S-Video. It is needed to connect the system unit with a mouse or keyboard. This element is designed to complement modern receivers or the latest models of equipment.
4. YPbPr. It is necessary in order to be able to transmit images in 1080i resolution. In this case, several cables are used, each of them has its own color.
5. HDMI. It allows you to show the picture as the operator broadcasts it. No changes or transformations occur in this case.

The company has set a goal to gradually switch to HDMI, this will allow all connected users to view clear images in HD format.

If you are wondering how to connect the Tricolor receiver to your TV, you can follow these steps:

• connect the antenna;
• connect to a television receiver.

To connect the antenna you need to do the following:

1. Take a coaxial cable.
2. Expose the core in the center. To do this, you need to unscrew the braid.
3. You need to take connector F and connect to the 2 ends of the wire.
4. Connect to the antenna.
5. The second end is connected to the LBM in receiver input.
6. The cable is fixed on the plate.

When the work is completed, check the reliability of the connection of all elements. The quality of the received signal depends on this.

At the second stage, the plate is connected to the equipment. First, the set-top box is checked to make sure there are outputs. To connect to the converter use LNB in. The socket through which you can connect an antenna is labeled LNB out.

Depending on what type of receiver is used, the set of connectors changes. It is useful to make sure that the firmware version is up to date. In this case, the picture can be broadcast to all outputs. But there are situations when users will have to choose which output to send the signal to.

You need to insert a high-frequency cable into the LNB out connector; as a result, an antenna will be connected. The receiver and TV will turn on, you will see the word Boot on the monitor, after which the channel number will become visible.

The TV owner needs to complete the setup, and then wait until the “No Signal” message becomes visible. Its appearance will mean that all operations were performed correctly. The remaining cables are connected in the same way and configured.

If there is an old TV in the room, but the owner decided to connect it, then for this you will need a “tulip”. It has 3 outputs, each marked with its own color. But this option has disadvantages; it will not be possible to transmit the image in high quality.

Since 2021, television channels began to be displayed in the lists, this was done for the convenience of users. If you need to set up Tricolor TV channels, the step-by-step instructions are as follows:

1. You need to turn on the TV, and then switch it to a mode that allows you to configure satellite channels. To do this, you need to select the antenna settings section in the menu.
2. Select the “Manual setting” menu item.
3. Before you start searching for channels, you need to make sure that the manual mode parameters are set: Network Search is enabled (this option is responsible for network search). Set the transponder frequency, select the symbol rate and satellite. The values ​​should be 12226, 27500 and Eutelsat 36E.
4. How to set up Tricolor channels is written in the instructions. You need to start searching for channels, and then perform the actions that will be written on the TV screen. During the process, data will be displayed about how the search is progressing and what channels are found.
5. When the search is completed, the TV owner must save the channel list.

When searching for channels, if the settings do not contain the necessary data, you can enter it manually.

On Samsung Smart TV

In order to properly configure the equipment, you must first familiarize yourself with the process.

In this case, the tuner model, antenna size, quality of synchronization equipment, as well as the TV model are of great importance.

How to set up Tricolor TV yourself if the settings on your Samsung Smart TV are lost? If any noise or ripples occur, please pay attention to ensure that the system is installed correctly. Measures must also be taken in the absence of channels that were previously broadcast.

To do this, debug the received signal level as follows:

• Enter the system menu in the “Signal Level” section and find the “Settings” option.
• Enter the password (standard value is 0000) and confirm the actions to be performed.
• Go to “System Settings” and click on the “OK” button.
• Select “Antenna settings” and select the list of channels in accordance with the region of use: EUTEL SAT 36V or 36A.
• Find 2 scales that indicate the signal level. They must be filled to 70%. In this case, the work was carried out correctly and no changes need to be made. In this case, you should pay attention to mechanical damage and unfavorable factors.

After completing the above steps, you can begin to fine-tune the system. Please note that the receiver must be registered if this procedure was not carried out during the contract process. Otherwise, the equipment will not function.

Receiver connection diagram

The antenna cable connecting the receiver to the TV must be connected to LNB IN - the output of the receiver. The cable type doesn't matter. The RF cable should be connected to the LNB OUT and the TV antenna socket.

After applying voltage to the receiving equipment, the “Boot” command will appear on the receiver’s display, indicating the start of the receiver’s operation. Next, the inscription will change to the channel number. You should search for channels on your TV. If the TV has been correctly connected to the tuner, the line “No signal” will appear.

To turn on other types of cables, using the TV remote control, select the working format of the incoming signal by pressing the “Sourse” (or “TV/AV”) key. Until the “No Signal” command is displayed. After completing the steps, you need to configure the satellite dish.

Connection diagram for two television receivers

To include a second TV receiver in the circuit, you will need an additional cable. If the first TV was connected using a “tulip” connector, then the second TV should be connected in a different way. It is important to note that the information signal must be supplied to all available receiver outputs.

Since the display is controlled from one receiver, the broadcast of channels will be the same on two TVs. If a subscriber wants to watch different channels, then he needs to purchase another tuner, which operates from the same antenna, but is connected through a different output on the converter.

To minimize signal loss, experts advise using as few wires as possible. The cable length should also not be too long.

To make your own cable, you need to purchase the required length of coaxial cable. Then the F-connector should be attached to one end so that the inner core of the cable protrudes at least 1 cm. The same should be done with the other end.

To connect and configure a second independent TV to display other channels, the user needs to purchase a splitter for the cable through which the broadcast is supplied. If only the HDMI output is used, you must use an HDMI divider that distributes the signal to the required number of TVs.

What to do if there is no picture

Sometimes users encounter a problem in which even correct configuration and registration of the receiver does not allow access to TV channels. In this case, you should immediately carefully check all cables and connections. Any damage affects the ability to transmit the signal.

No signal when connected

Next, you should check the signal level when adjusting the antenna. You can try to repeat the procedure for adjusting the position of the plate.

Access to channels will not be provided if the user has not paid the subscription fee. It is worth making sure that the funds are transferred to the company’s account, and if problems arise, contact the support team.

If none of the described methods help, it is recommended to call the company’s specialists who will come and perform all the necessary procedures.

Methods of laying wires

Some users of satellite services prefer to use a special device - a video sender - instead of wires. The device, consisting of two blocks, is connected between the TV and the tuner and transmits the signal via Wi-Fi. The maximum allowable distance is 30 m. Since this device has all kinds of connectors, it has no problems in installation. Wired video senders are less expensive, but their use does not solve the problem of unnecessary wires.

Another way that makes it possible for two TVs to operate independently of each other is to purchase a special Tricolor TV set, which includes a receiver consisting of two tuners.